Merry Christmas to everyone!
One more day of Christmas, I didn't make it in time for the 12 days of Christmas.
I am still trying to incorporate or use recycled items.
Remember the aluminum Christmas trees growing up? My grandparents had one. Not only aluminum but it spun in its base! When you are little that is a major Ooo and Ahhh + Pretty Shiny.
On a smaller scale using aluminum cans, here is my rendition.
Aluminum soda cans aren't any thicker than index stock, just a different material that behaves in it's own way. It will rip, fold and get indentations on it the same way as paper but with aluminums reflective nature it's far more noticeable.
Materials:
3 Aluminum Cans, I used Green Sprite Cans
Anodized Aluminum Jump Rings
Glass Beads
24 Gauge Copper wire
18 Gauge Copper Wire
Art Bead
Metal Eyelets, found in the scrapbooking section
Tools:
Sharp Scissors
Mini Anvil
Ball Pein Hammer
1/8" Paper Punch
Eyelet Punch Tool
Round and Chain Nose Pliers
Sharpie Marker
Ruler
Paper Pattern
Tape
Glue Dots
Any other tool that helps!
Directions:
1. Cut the top and bottom off of your cans as straight and cleanly as possible. After cutting so many cans you will find a technique that works for you. You may want to practice on a can that you do not intend on using for this project.
My method: find the side of the can with the UPC code. Take a knife and carefully push/cut through the can at the top and bottom, making a slit. Holding the top of the can in your left hand put the tip of your scissors into the slit and begin cutting. Holding tightly onto can try to keep your scissors straight and pointing upwards, turning the can as you cut. The tension will be forcing you to cut downwards. After you have successfully cut off the top, cut the can from top to bottom to the other slit. This cut helps to ease the tension of cutting the bottom off. Hold the bottom of the can with your left hand, insert your scissors and start cutting. Even up the edges.
2. Make your pattern. I used a scrap piece of paper. Trace your pattern onto the can and cut out.
3. Roll your half circle can into a cone shape. Tape it in place. At this point you will need to punch your first hole for the eyelet. Measure up from the bottom the can. Calculate the size of your jump rings and space from the edge. Mine measure 1/4" from the bottom. Place your eyelet, using the eyelet tool and hammer strike the eyelet to spread and form. I put in 2 more eyelets above the bottom one and it's a challenge. You can choose to use glue, glue gun or glue dots to hold down the seam. If necessary trim the bottom.
4. Measure on the curve edge where you are going to punch holes for the dangling beads. Mine are 1/4" up and spaced 1/2" apart. Punch the holes and dap in the eyelets.
5. Measure 6" of 18 gauge copper wire for the hanger. Form loop or curly cue then slide a bead that will prevent the wire from coming out the top and help the aluminum keep it's shape.
6. Place your art bead in the wire on top of the cone. Place a glass bead on top of the art bead.
Helpful hint: I used the eyelets in the large holes of the beads for a more attractive look and keep them from flopping side to side.
7. Bend the wire 90º, then wrap the wire around your round nose pliers to form a loop. Use a paintbrush handle or dowel to form the hook. With your round nose pliers form a loop on the tip of the hook .
8. Cut the top and bottom off of the 2 remaining cans. Flatten out and measure in quarter inch increments to cut strips for the curly branches. Cut the cans into strips.
9. Using a popsicle stick or other item you like better, curl the can as you would ribbon. Color side up, place your stick approximately an inch up, scrape the stick quickly to create the curl. This may take a couple times to make the curl. They can be rolled up and adjusted by hand later after they are attached.
10. Starting at the bottom and in between to eyelets, place the first row of curly strips. My glue dots are singles so I cut them in half to glue the top and bottom of the curl strip to the cone base. Place the nexxt row 3/4" to 1" up and between the first row. Repeat for the remainder of the rows.
11. For the 1" dangling beads cut 2.5" of 24 gauge copper wire. Make a curly cue on the end of the wire then bend 90º and slide bead on. Bend wire at top of bead 90º, make a loop with your round nose pliers and wrap wire.
12. Attach the dangling beads with anodized aluminum jump rings alternating colors.
I promised I would show my Ornament of the year while I was participating in the blog hop.
I had to abandon the original design. Here is the new design.
Funky Snowman
My question this Studio Saturday is:
"If you could have one bead artist fill up your stocking, who would you pick?"
Leave your answer to the question on ArtBeadScene.com and you could win
Thanks to Heather for this giveaway. I want to win it!
Have a wonderful holiday
may you have peace within.
Posts
